REC and WS500 User Forum
Forum breadcrumbs - You are here:REC-BMS and WS500 Smart Regulator Users ForumPost History: gregory smith
Post History: gregory smith

gregory smith
User
Yep, poles+12 and pully ratio is at least close. So I dont know if the reported engine RPM of 55 is …In: Wakespeed regulators not driving
5 months ago
Is engine RPM as reported in AST equal to actual RPM or in 10's? I finally have Tach working bu …In: Engine RPM reporting
5 months ago
Yep. The config guide is a little confusing... at the header of the SCT instructions, it says no cha …In: Wakespeed regulators not driving
5 months ago
Hi Peter,
My stator wire is connected, but I am not reading engine RPM. I have not "ignored& …In: Wakespeed regulators not driving
5 months ago
thanks.
PBF is set to 1 and WS500 does not read engine RPM. So if PBF needs tach data, then this …In: Wakespeed regulators not driving
5 months ago
Good morning!
I am using a customized version of #7. The exit amps settings in #7 dont work for m …In: Wakespeed regulators not driving
5 months ago
Thanks, Firefly bats so no BMS. Dual engine. Controlling WS500 flashing Green Acceptance, slave WS50 …In: Wakespeed regulators not driving
5 months ago
Hi,
Batteries were at 50% leaving the anchorage but max output from dual big alternators was 95A. …In: Wakespeed regulators not driving
5 months ago
Thanks Ben, I am pretty close to those settings;
CPA I am using 420 minutes and 3A for exit A
…In: Float voltage not consistent
6 months ago
Looks like there is an added field in CPB to set max V with 2.5 but it isnt adjustable in the config …In: Max V settings in CPB
6 months ago
can only study exactly what goes wrong, when you post a full log, and point to the exact t …In: Float voltage not consistent
6 months ago
Just finished a long run down the coast. Issue I am having is WS500 sometimes transitions to correct …In: Float voltage not consistent
6 months ago
100% SOC progress
With latest config was able to see ACC to Float at 5A. Very close to target. If …In: Achieving true 100%SOC
7 months ago
Yep, I probably asked the MS tech the wrong question. The MS CAN bus output is digital but I could h …In: Achieving true 100%SOC
7 months ago
would have been sweet to use the same shunt but the MS shunt converts to a digital message and no wa …In: Achieving true 100%SOC
7 months ago
Thanks,
I am reading tail current from Mastervolt closed loop network on the Mastervolt remote di …In: Achieving true 100%SOC
7 months ago
Thanks Ben,
Bat Cap Multiplier. Lots of places in the WS manuals where it says system is design …In: Achieving true 100%SOC
7 months ago
Ben, Much appreciate the detailed response. Here is where I am:
just updated firmware to latest …In: Achieving true 100%SOC
7 months ago
If my set-up had been one and done, the USB would be fine. But I am still fussing and have had the c …In: Better access while running
7 months ago
thanks, I should have rephrased all that about the alternators. My guess is, they are putting in as …In: Twin engine installation with 2 WS500
7 months ago
I have the same question and I cant see anywhere in the manual that discusses the twin engine/twin s …In: Twin engine installation with 2 WS500
7 months ago
Jon, I have a similar issue: system drops to Float early. I dont think I am pulling amps down at the …In: WS500 switches to float early
7 months ago
REC/WS500 User Forum Search
Recent forum posts




