The Thermometer performs measurements within the range from -55 to +125°C (-67..+257°F), the sensor is placed outside the case on a flexible, 95cm wire in a sealed stainless steel sleeve and can be used to measure the temperature of gases or liquids. If necessary, the wire can be elongated up to 100 meters. The Thermometer can be configured by the user to display data as “Air temperature”, “Sea temperature”, “Temperature in the refrigerator”, “Temperature in the engine room”, “Bait Well Temperature”, etc.
The Thermometer performs measurements within the range from -55 to +125°C (-67..+257°F) with absolute measurement accuracy of ±0.5°C.
The sensor is placed outside the case on a flexible, 95cm wire in a sealed stainless steel sleeve and can be used to measure the temperature of gases or liquids. If necessary, the wire can be elongated up to 100 meters. The Thermometer can be configured by the user to display data as “Air temperature” (factory setting), “Sea temperature”, “Temperature in the refrigerator”, “Temperature in the engine room”, “Bait Well Temperature”, etc.
Temperature data output resolution to a NMEA 2000 network is 0.01°C, absolute measurement accuracy is ±0.5°C. To measure extremely hot temperatures we can recommend our Exhaust Gas Sensor YDGS-01, but it has much lower accuracy. For air temperature you can choose our , it will also provide you with relative humidity and calculated dew point temperature.
The Thermometer is plug and play. You only need to connect it to NMEA 2000 to get readings on any or instrument display. It can be used to monitor fridges and freezers bait wells, air or sea temperature. Up to 50 devices may be used on a vessel simultaneously; this limitation is set by the network specification.
NMEA2000 Micro Male, Raymarine Seatalk NG
Yacht Devices are shipped Free via Air Mail directly from the manufacturer in Europe. Expected delivery is 2-3 weeks from receipt of order. Duty and import costs, if applicable, are not included in the price.
WS500 Smart RegulatorFrom:
Bonus !! Buy One and get the WS500 configuration Tool Free, a $ 24.95 value!
Buy two and get the Pro version Free,
a $ 149.95 value!
And if you build it as a kit you save 10% on all accessories !!
(versus ordering items individually)
The WS500 is a next generation Smart Regulator for Marine, Off-grid and RV applications. It is ideally suited to the latest in battery technology and includes CANBus and NMEA2k communications to integrate into an overall Energy Management Network. Select your Wiring harness based on whether you need positive or negative type alternator excitation. You WILL need either a Positive or Negative Wiring Harness. Make sure you include it when you buy. You may also wish to include a battery temperature sensor wiring harness. This is optional but is strongly recommended, especially in “Battery Centric” configurations where the WS500 can reduce its output when your battery starts to warm up.
Scroll down to select your options:
3kW DC-DC Energy Management System
$2,499.95Add to cart
• Charge higher voltage batteries utilizing existing chassis electrical system.
• On demand supplemental chassis electrical system power to support surge loads without
cost of additional batteries.
• Replace existing chassis alternator with higher energy unit and transparently support legacy
chassis power bus.
• J1939/RV-C based CAN support for system and BMS integration.
• Compatible with additional WS500 controlled alternators installed in same system
NMEA 2000 Bridge YDNB-07
Unifies two physical NMEA 2000 networks into a single logical network, smoothly exchanging messages between them. The Bridge also support filtering and processing of transmitted messages and contains a built-in compiler of a simple programming language. You can create message processing programs on any device with a MicroSD socket and a text editor. One of the CAN-interfaces on the device has high-voltage galvanic isolation and can operate at a higher supply voltage.
NMEA 0183 Multiplexer YDNM-02
$149.00Add to cart
Smart multiplexer with five NMEA 0183 ports and one SeaTalk port, auto detection of port speed and easy configuration with a click of a button! And, of course, it has flexible filters, routing rules, and supports firmware updates.
The underlying idea was to create simplest multiplexer in the world. In our lab, the project was called “Simple Multiplexer”, but later we added a lot of features and removed the word “Simple”. Nonetheless, we are sure that it is still the easiest to install. Instead of a laptop and software, you’ll only need a paperclip.