
Circuit Control YDCC-04
$289.00 $260.10
The Circuit Control contains four latching (bi-stable) relays, which can be managed from connected control buttons with LED indicators or over NMEA 2000 with standard messages.
You can manage loads connected to the Circuit Control (firmware 1.01 or later is required) from most modern chart plotters with CZone support.
The Circuit Control and Switch Control are designed to be compatible with Oceanic Systems, Offshore Systems, Chetco Digital, Maretron and Carling Tech displays and relay modules, and with other NMEA 2000 digital switching devices managed with standard NMEA 2000 PGN 127501 “Binary Status Report” and PGN 127502 “Binary Switch Control”.
Product benefits:
- compatible with a wide range of equipment, including modern chart plotterts;
- no special requirements for buttons, you can choose any momentary push buttons to match your boat’s interior;
- no special knowledge, software or hardware is required for installation;
- price and size are suitable for small vessels;
- any type of load is allowed (AC, DC, audio);
- no heating, no extra power consumption;
- pure NMEA 2000 product, compliant to the Standard and certified by NMEA;
- high-voltage isolation with the load;
Device terminals are shown in Appendix C. Electrical characteristics of the Circuit Control:
four channels: two with normally open contacts (ON-OFF) and two with switching contacts;
latching (bi-stable) relays consume electricity only during the process of switching and stay in their last state after the device is powered off;
maximum constant load current per channel is 10A, peak is 20A (4 seconds, duty cycle 10%);
capable of switching the direct current (DC) and alternating current (AC) loads up to 400 V;
high voltage isolation with a load, 5000 VRMS;
average device consumption is only 30 mA.
Two independent digital switching systems (different bank numbers)
Figure 4. Two independent digital switching systems (different bank numbers)
Basic system, with single Circuit Control unit
Figure 1. Basic system, with single Circuit Control unit
Typical system, with multiple control panels
Figure 2. Typical system, with multiple control panels
Parallel loads, synchronized Circuit Control units
Figure 3. Parallel loads, synchronized Circuit Control units
Two independent digital switching systems (different bank numbers)
Figure 4. Two independent digital switching systems (different bank numbers)
Basic system, with single Circuit Control unit
Figure 1. Basic system, with single Circuit Control unit
The Circuit Control unit can work in parallel with other units and can be managed from multiple Switch Control units with a matched bank number (252 unique bank numbers are allowed in NMEA 2000). Multiple independent digital switching systems (with different bank numbers) can co-exists in a single NMEA 2000 network. Use the slider shown in the above diagram to check examples of digital switching systems.
Product Images
Shipping-YD
Yacht Devices are shipped Free via Air Mail directly from the manufacturer in Europe. Expected delivery is 2-3 weeks from receipt of order. Duty and import costs, if applicable, are not included in the price.
You may also like…
-
Switch Control YDSC-04
$149.00$134.10Add to cartThe additional control post. The Switch Control allows viewing of the state and the management of four channels of an NMEA 2000 switch bank from the connected buttons with LED indicators. It is designed to work in tandem with Circuit Control YDCC-04 (contains four latching relays) and is compatible with other NMEA 2000 digital switching devices managed by standard NMEA 2000 PGNs 127501 and 127502.
Related products
-
Smart Relay YDSR-01
$69.00$62.10Add to cartThe device helps you when you have two loads and only one power switch. For example, you have a combined deck/steaming light on the mast and only two wires (positive and negative) inside the mast. Smart Relay powers the first channel when you turn the power switch on, and it powers the second channel when you cycle the power switch twice in one second. Contains a bi-stable relay and uses power only when channels are switching; at all other times it consumes less than 0.5 mA.
-
CAN Log Viewer
Add to cartCAN Log Viewer is designed to view and analyze live data from NMEA 2000 and J1939 networks, as well as log files recorded by our products and Raymarine chart plotters. This software can configure and update the firmware of our products not eqipped with a MicroSD card, and display historical data from sensors. Works on Microsoft Windows, Linux and Max OS X.
REC/WS500 User Forum Search
Recent forum posts




Reviews
There are no reviews yet.