Dynamic Product Search

Smart Energy Management for Marine and Off Grid


No products in the cart.

Category: Network


Showing 1–12 of 21 results

  • WS500 Victron Crossover Cable


    WakeSpeed WS500 RJ45  to Victron Energy RJ45 VE-CAN crossover cable

    Add to cart
  • Barometer YDBC-05


    The Barometer is intended for measuring atmospheric pressure within the range from 300 to 1100 hPa (mbar). The sensor is located inside the device case. Many chartplotters and digital navigation instruments are able to display data on pressure in the form of graphs or show a trend indicator; this allows tracking of trends in the weather change. The Device dimensions, including the connector, are 54x20x20mm, the mass is only 11 grams, so it is suitable for racing yachts. Pressure data output resolution 0.01 hPa (mbar), absolute measurement accuracy is ±1 hPa, relative measurement accuracy is ±0.12 hPa.

    Select options
  • Engine Gateway YDEG-04


    Gateway for Volvo Penta, BRP Rotax, SmartCraft (Mercury, Mercruiser) and J1939 engines to NMEA 2000 marine electronics network. It will provide you with engine revolutions, motor hours, coolant temperature, battery voltage, warning and alarms, fuel rate and other data on the screen of your chart plotter. No extra cables required in most cases thanks to a built-in Y-connector.

    Select options
  • NMEA 2000 Wi-Fi Router YDNR-02N


    Yacht Devices is pleased to present the most anticipated product of the season: NMEA 2000 Wi-Fi Router YDNR-02N, equipped with one NMEA 2000, two NMEA 0183, and one SeaTalk ports and Wi-Fi. It combines the best features of our NMEA 2000 Wi-Fi Gateway and NMEA 0183 Wi-Fi Router.

    Read more
  • Thermometer YDTC-13


    The Thermometer performs measurements within the range from -55 to +125°C (-67..+257°F), the sensor is placed outside the case on a flexible, 95cm wire in a sealed stainless steel sleeve and can be used to measure the temperature of gases or liquids. If necessary, the wire can be elongated up to 100 meters. The Thermometer can be configured by the user to display data as “Air temperature”, “Sea temperature”, “Temperature in the refrigerator”, “Temperature in the engine room”, “Bait Well Temperature”, etc.

    Select options
  • NMEA 0183 Gateway YDNG-03


    Allows you to connect NMEA 0183 equipment to a NMEA 2000 network and vice versa. It has a bi-directional converter with wide support of message types including AIS. The configurable baud rate from 300 to 115200 baud for the NMEA 0183 port allows connection of AIS transceivers (38400 baud), fast NMEA 0183 multiplexers and PC adaptors, as well as standard NMEA 0183 equipment.

    Select options
  • Humidity Sensor YDHS-01


    Provides chart plotters and instrumental displays with humidity and air temperature measurements and calculated dew point temperature. High quality sensor with ±2 % RH and ±0.3 °C accuracy in most of the operating range. The device is plug and play; you only need to plug it into a NMEA 2000 backbone to get readings on all chart plotters and instruments on board.

    Select options
  • WIFI Gateway, Yacht Devices YDWG02


    If you wish to see marine data from a smartphone, you should choose the Wi-Fi Gateway. It can join an existing Wi-Fi network on board or establish its own. It is also a bi-directional gateway, and can also convert NMEA 2000 to NMEA 0183 and vice versa for compatibility with outdated software. The Web Gauges page of the internal website allow viewing of realtime vessel data (position, depth, wind, course and speed, engine, etc.) using a web browser on PC, laptop, tablet or smartphone.  This listing is for the item on the right that connects to your NMEA2000 network.

    Select options
  • Exhaust Gas Sensor YDGS-01


    The Sensor measures the temperature of extremely hot gases, solids and liquids within the range from 0 to +800 °C (+32 to 1472 °F). The Sensor can be configured by the user to display data as “Exhaust gas temperature”, “Air temperature”, “Heating system temperature”, “Engine room temperature”, etc. The Device is plug and play; you only need to plug it into a NMEA 2000 backbone to get readings on all chart plotters.

    Select options
  • J1708 Engine Gateway YDES-04


    A gateway for engines with a J1708 serial interface to a NMEA 2000 marine digital network. It supports the two protocols that work over J1708: the standard J1587 used by many manufacturers and the proprietary Volvo Penta protocol used in engines with EDC I, for example KAD 44 and KAD 300. A J1708 interface is used for connection of gauges, electronic displays, diagnostics equipment and other vehicle modules. This interface was very popular until 2005-2007, when it began to be quickly replaced by the J1939 protocol that is based, the same as NMEA 2000, on a faster CAN network.

    Select options
  • Tank Adapter YDTA-01


    NMEA 2000 adaptor allows you to connect an existing resistive type fluid level sensor (EU, US, JP or custom) installed on a tank and display the fluid level on NMEA 2000 devices, including chart plotters and instrumental displays. The Adaptor can be configured to report one of the seven fluid types defined in the NMEA 2000 standard: Diesel Fuel, Gasoline Fuel, Oil, Fresh Water, Waste Water, Black Water (Sewage), or Live Well. Can be installed as a standalone measuring device or in parallel with an existing analog gauge or Volvo Penta MDI.

    Select options